Stay ConnectedA woodworking show for modern woodworkers and makers. Join Marc Spagnuolo, Shannon Rogers, and Matt Cremona for a light-hearted look at the latest news, tips, and tricks from the world of woodworking.
Hosted on Acast. See acast.com/privacy for more information.
Copyright: © 2024 Wood Talk | Woodworking
Marc and Matt answer listener questions about recognizing dull jointer and planer knives, leaving the right clearance for inset wooden drawers, creating low-friction shop surfaces, and deciding how much extra lumber to buy for a project. They also discuss the “buy 20% extra” lumber rule, basic woodworking toolkits, Marc’s costly encounter with insect-damaged wenge, and some of the other woodworking podcasts and resources available online.
Hosted on Acast. See acast.com/privacy for more information.
Marc returns from AWFS with stories about granite-top power tools, a major move toward riving knives on table saws, and finally meeting Norm Abram, with a little encouragement from Nicole.
Marc and Matt also discuss exposed Festool Domino tenons, putting casters under large shop machines, flush-trim router bit sizes, a new PBS woodworking show, and Marc’s $17 curly maple lumberyard score.
Hosted on Acast. See acast.com/privacy for more information.
Marc and Matt spend much of this episode sorting through one of woodworking’s most confusing subjects: choosing a finish.
Marc starts by explaining the difference between evaporative finishes, such as lacquer and shellac, and reactive finishes, such as oil-based varnish and catalyzed lacquer. Evaporative finishes are generally easier to repair because a new coat or the proper solvent can soften and blend with the existing finish. Reactive finishes tend to offer more protection, but each coat cures as a separate layer and repairs can be more difficult.
They also break down several common finish types:
Oils, such as linseed oil and tung oil, soak into the wood rather than building much of a protective film. They are easy to apply and bring out the depth and color of the wood, but offer limited protection and often need to be renewed over time.
Varnishes, including polyurethane, provide much better resistance to scratches, heat, and solvents. They can be brushed, wiped, or sprayed, but some woodworkers dislike the heavier film or “plastic” look that can come with certain products.
Oil/varnish blends offer a middle ground. They are easy to wipe on like an oil but provide more protection as additional coats build. Marc recommends them as a good place for newer woodworkers to start, though they generally require more coats and drying time than straight varnish.
The show also includes a follow-up to a question about hand-plane blades: the steel Matt was trying to remember is O1 steel.
Marc and Nicole will be at the Festool booth during the AWFS show in Las Vegas, and Matt mentions the “Win a Weekend with Norm” sweepstakes and the Podcast Awards at PodcastAwards.com.
Hosted on Acast. See acast.com/privacy for more information.
Marc and Matt tackle one of every woodworker’s favorite subjects: tools. Which tools are essential, which do they wish they had bought sooner, which purchases do they regret, and which inexpensive tools turned out to be great values?
They also cover PVC versus metal dust collection, a rubber shelf-liner finishing disaster, affordable hardwoods for beginners, optimizing plywood layouts with CutList Plus, preventing rot in outdoor furniture, restoring vintage Powermatic machines, and choosing veneer backings.
Hosted on Acast. See acast.com/privacy for more information.
Marc and Matt dig into HVLP spray finishing, including turbine systems, spraying stains, gun technique, pressure pots, basement safety, and gravity-feed versus pressurized cups.
They also cover plywood versus solid wood, whether woodworking school is worth it, small-shop dust collection, connecting a DeWalt DW621 to a shop vac, specialty hand planes, sanding routed profiles, the Festool Domino, SawStop, and free cabinet-design software from eCabinetSystems.com.
Hosted on Acast. See acast.com/privacy for more information.
Marc and Matt compare Scary Sharp with diamond stones for sharpening chisels and plane irons, including cost, speed, durability, and where each method works best.
They also cover table saw blade cleaning, air compressor sizing, plywood joinery, the Powermatic PM2000 vs. PM66, repairing a finish after sanding through the color, double-sided tape, keeping cabinets square during assembly, and whether a spiral cutterhead is worth the extra cost on a jointer.
Hosted on Acast. See acast.com/privacy for more information.
The listener questions start with Wilbur asking about jointing boards with hand planes versus using a power jointer. Marc and Matt explain why a hand plane can work a long board in sections, while a power jointer requires the entire board to travel across the beds in one pass.
Skee asks about mixing wood species in the same project. Marc and Matt agree there are no strict rules. Grain, color, and the overall look should drive the choice, with contrasting or exotic woods often working best as accents. J.T. also reports great results with his new Leigh FMT mortise-and-tenon jig, praising its speed and repeatable fit.
A listener dealing with moisture in his shop asks how to remove rust from cast-iron tool tops and keep it from returning. Marc discusses cleaning the surface with an abrasive and mineral spirits, then protecting it with products such as Boeshield T-9 and a silicone-free wax. Later in the show, a listener follows up with his own long-term use of WD-40, leading to more discussion about rust prevention.
They also tackle twisted, cupped, and warped lumber. Matt suggests cutting problem boards into shorter pieces when possible, while Marc stresses that sometimes the best answer is to scrap a board rather than force unstable stock into a project. Skee follows with a question about sizing furniture parts for the loads they need to carry, and Matt points listeners toward the furniture and project-design resources at WoodBin.
Daryl asks one of the bigger questions of the episode: should you cut dovetails by hand or use a router jig? Marc and Matt discuss the advantages of both approaches, along with pins-first versus tails-first methods and Japanese versus Western saws. There is no single right answer. A jig provides fast, repeatable results, while hand-cut dovetails require more practice but offer a different woodworking experience. Daryl also asks about tuning older Bailey and Stanley planes, and Matt directs him to his hand-plane videos at Matt’s Basement Workshop.
Another listener asks about wood toxicity. Marc’s main advice is not to treat any wood dust as harmless and to use proper dust protection regardless of species. The original show notes also point to Health Hazards in Woodworking and the Botanical Database for more information.
The questions continue with loose mortise-and-tenon joints, planer recommendations, and Marc’s experience working with David Marks. Marc explains that his time in David’s shop was not a traditional paid apprenticeship and points listeners to djmarks.com for information about David’s work and classes.
Louis asks about finishing a cherry bed for his baby daughter. Marc and Matt discuss shellac as a good option and how its warm tone works with cherry. They also talk about application methods and whether additional oil or wax is needed.
Finally, Kevin asks about combination jointer-planer machines. Marc and Matt both prefer separate machines when shop space allows. For someone who already owns a lunchbox planer, they recommend putting the money toward an 8-inch jointer rather than replacing both tools with a combination machine.
Hosted on Acast. See acast.com/privacy for more information.
Marc and Matt start with updates from around the woodworking world, including the winners of the Video Shop Tour Challenge, a clever Rockler gift-card promotion, and Marc’s new Makita 18V lithium-ion drill. They also dig into a survey from Cabinet Maker Magazine about small woodworking shops, including who runs them, how many hours they work, how they learned the trade, and the challenges of turning woodworking skills into a profitable business.
The listener questions begin with a common tool-buying dilemma: should a furniture maker buy a bandsaw or a jointer first? Both Marc and Matt choose the jointer. For someone building furniture and tables, the ability to flatten and square rough lumber opens up more material choices and can save money over time. They also explain how French cleats work and why spreading the load across several wall studs makes them such a useful way to hang cabinets and shop storage.
Another listener is planning a parquet floor and asks about patterns and construction methods. Marc and Matt suggest researching designs through the library, Amazon, and woodworking forums, while also considering how the floor’s pattern and materials will move. The discussion then shifts to accuracy in furniture making. Marc explains relative dimensioning, where parts are marked and cut to fit one another instead of relying on measurements alone, while Matt talks about marking knives and gauges.
J.T. asks how to work more efficiently in the shop. Marc and Matt recommend planning the work, using cut lists, grouping similar operations together, and setting clear goals for each shop session rather than constantly switching tasks.
They also discuss a glue used by David Marks that appeared not to foam. Marc explains that polyurethane glue normally does foam and suggests that the product may have been plastic resin glue instead. For outdoor projects, he also recommends Titebond III as a simpler waterproof option.
The show wraps with a comparison of sliding compound miter saws and radial arm saws. Marc and Matt favor the sliding compound miter saw for its smaller footprint, portability, and versatility in a modern shop. Finally, they tackle lining vise jaws with leather and point listeners toward the hand-tool discussions at WoodNet and Christopher Schwarz’s work for more information.
Hosted on Acast. See acast.com/privacy for more information.
Marc introduces a new way to submit questions to Wood Talk: voicemail. Matt also talks about his Router Bit of the Month series with Woodcraft and Whiteside Machine Company, including the Classic Pattern Profile bit, which combines a cove with a roundover.
Marc explains relative dimensioning, the practice of cutting parts to fit the project rather than relying on exact measurements for every piece. The conversation then turns to favorite finishes. Marc leans toward wiping varnish and oil-varnish blends, while Matt tends to stick with polyurethane. Marc also describes a Fine Woodworking video from Andy Rae showing a final topcoat made from boiled linseed oil, varnish, and pore filler to create a smooth surface on open-grained wood.
The first listener voicemail asks for drill press recommendations. Marc and Matt compare benchtop and floor-standing models, variable speeds, lasers, and other useful features. Marc also mentions the Powermatic drill press sitting on his wish list.
Another listener asks whether growth rings should alternate when gluing up a panel. Matt has never paid much attention to the old “bark up, bark down” rule, and Marc questions how much difference it makes in a properly built project. Both put more weight on choosing the best-looking faces and matching the grain.
They also compare lever and handwheel adjustments on jointer tables before getting into one of the larger discussions of the episode: clamps. How many do you need, how far apart should they be, and how much pressure is enough? Marc and Matt discuss clamp placement, cauls, glue squeeze-out, and the problems caused by using more pressure than the joint needs. Even squeeze-out along the joint is a useful sign that pressure is being applied where it belongs.
The episode wraps with a question from Gordon in Australia about decorative inlay in a solid-wood coffee table. Marc explains that thin inlay is flexible enough to move with the surrounding wood, so normal seasonal movement should not create a problem.
Hosted on Acast. See acast.com/privacy for more information.
Marc and Matt tackle a wide range of listener questions, starting with how to create the thick poured finish commonly seen on bar tops. Marc recommends a two-part epoxy-style finish and points listeners to Klockit for finishing supplies. They also cover large panel glue-ups, using biscuits for alignment, parallel clamps and cauls, and ways to joint stock when you don’t own a jointer.
A larger discussion compares mortise-and-tenon joinery with biscuits, pocket holes, and dowels, including where each method makes sense for a coffee table. They also explain how to avoid tearout when cutting tenons and work through the hand-tool skills worth learning first, including sharpening, chisels, block planes, card scrapers, and hand saws. The show wraps with tips for cutting detailed letter inlays on the scroll saw, plus a thank-you to listener Bob for sending a box of candy.
Hosted on Acast. See acast.com/privacy for more information.
Our TOPPODCAST Picks 
